? semiconductor components industries, llc, 2003 february, 2003 - rev. 3 1 publication order number: nl17szu04/d nl17szu04 single unbuffered inverter the nl17szu04 is a single unbuffered inverter in two tiny footprint package. the device performs much as lcx multi-gate products in speed and drive. ? tiny sot- 353 and sot- 553 packages ? source/sink 16 ma at 4.5 v v cc ? over-voltage tolerant inputs and outputs ? pin for pin with nc7szu04p5x, tc7szu04fu and tc7szu04afe ? chip complexity: fets = 20 ? designed for 1.65 v to 5.5 v v cc operation figure 1. pinout (top view) figure 2. logic symbol 1 a y v cc nc a 1 2 3 5 4 gnd y marking diagrams l6 d sot-353/sc70-5/sc-88a df suffix case 419a sot-553 xv5 suffix case 463b l6 = device marking d = one digit date code l6 d 1 5 1 5 1 5 1 5 see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information http://onsemi.com d = date code input function table output y = a y h l a l h pin assignment pin 1 2 3 4 5 function nc a gnd y v cc
nl17szu04 http://onsemi.com 2 maximum ratings symbol parameter value unit v cc dc supply voltage 0.5 to 7.0 v v in dc input voltage 0.5 to 7.0 v v out dc output voltage 0.5 to 7.0 v i ik dc input diode current 50 ma i ok dc output diode current 50 ma i out dc output sink current 50 ma i cc dc supply current per supply pin 100 ma t stg storage temperature range 65 to 150 c t l lead temperature, 1 mm from case for 10 seconds 260 c t j junction temperature under bias 150 c ja thermal resistance sot- 353 (note 1) sot- 553 350 496 c/w p d power dissipation in still air at 85 c sot- 353 sot- 553 186 135 mw msl moisture sensitivity level 1 f r flammability rating oxygen index: 28 to 34 ul 94 v-0 @ 0.125 in v esd esd withstand voltage human body model (note 2) machine model (note 3) charged device model (note 4) class ic class a n/a v maximum ratings are those values beyond which damage to the device may occur. exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. functional operation under absolute maximum-rated conditions is not implied. functional operation should be restricted to the recommended operating conditions. 1. measured with minimum pad spacing on an fr4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 2. tested to eia/jesd22-a114-a, rated to eia/jesd22-a114-b. 3. tested to eia/jesd22-a115-a, rated to eia/jesd22-a115-a. 4. tested to jesd22-c101-a. recommended operating conditions symbol parameter min max unit v cc dc supply voltage (operating) data retention only 1.65 1.5 5.5 5.5 v v in dc input voltage 0 5.5 v v out dc output voltage 0 5.5 v t a operating temperature range -40 +85 c t r , t f input rise and fall time v cc = 3.0 v 0.3 v v cc = 5.0 v 0.5 v 0 0 100 20 ns/v
nl17szu04 http://onsemi.com 3 dc electrical characteristics v cc t a = 25 c 40 c t a 85 c symbol parameter condition v cc (v) min typ max min max unit v ih high-level input voltage 1.65 to 1.85 0.85 v cc 0.85 v cc v 2.3 to 5.5 0.8 v cc 0.8 v cc v il low-level input voltage 1.65 to 1.85 0.15 v cc 0.15 v cc v 2.3 to 5.5 0.2 v cc 0.2 v cc v oh high- level output voltage v in = v il or v ih i oh = -100 a i oh = -3 ma 1.65 to 5.5 1.65 v cc - 0.1 1.29 v cc 1.52 v cc - 0.1 1.29 v v in = v il or v ih i oh = -4 ma 2.3 1.9 2.1 1.9 i oh = -6 ma 2.7 2.2 2.4 2.2 i oh = -8 ma 3.0 2.4 2.7 2.4 i oh = -12 ma 3.0 2.3 2.5 2.3 i oh = -16 ma 4.5 3.8 4.0 3.8 v ol low- level output voltage v in = v ih or v oh i ol = 100 a i ol = 3 ma 1.65 to 5.5 1.65 0.08 0.1 0.24 0.1 0.24 v v in = v ih or v oh i ol = 4 ma 2.3 0.20 0.3 0.3 i ol = 6 ma 2.7 0.22 0.4 0.4 i ol = 8 ma 3.0 0.28 0.4 0.4 i ol = 12 ma 3.0 0.38 0.55 0.55 i ol = 16 ma 4.5 0.42 0.55 0.55 i in input leakage current v in = v cc or gnd 0 to 5.5 0.1 1.0 a i off power off- output leakage current v out = 5.5 v 0 1 10 a i cc quiescent supply current v in = v cc or gnd 1.65 to 5.5 1 10 a ac electrical characteristics t r = t f = 3.0 ns v cc t a = 25 c 40 c t a 85 c symbol parameter condition v cc (v) min max min max unit t plh propagation delay (fi d ) r l = 1 m c l = 15 pf 1.8 0.15 1.0 11.7 1.0 12.1 ns t phl (figure 3 and 4) r l = 1 m c l = 15 pf 2.5 0.2 0.8 6.2 0.8 6.5 r l = 1 m c l = 15 pf 3.3 0.3 0.5 4.5 0.5 4.8 r l = 500 c l = 50 pf 1.0 6.0 1.0 6.5 r l = 1 m c l = 15 pf 5.0 0.5 0.5 3.9 0.5 1.0 r l = 500 c l = 50 pf 0.8 5.0 0.8 5.5 capacitive characteristics symbol parameter condition typical unit c in input capacitance v cc = 5.5 v, v i = 0 v or v cc 4.5 pf c pd power dissipation capacitance () 10 mhz, v cc = 3.3 v, v i = 0 v or v cc 6.5 pf (note 5) 10 mhz, v cc = 5.5 v, v i = 0 v or v cc 10 5. c pd is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption with out load. average operating current can be obtained by the equation: i cc(opr ) = c pd v cc f in + i cc . c pd is used to determine the no-load dynamic power consumption; p d = c pd v cc 2 f in + i cc v cc .
nl17szu04 http://onsemi.com 4 figure 3. switching waveform input r l c l a 1- mhz square input wave is recommended for propagation delay tests. figure 4. test circuit t f = 3 ns v cc gnd v oh v ol 90% 50% 10% 50% t plh t phl output y input a and b t f = 3 ns 90% 50% 10% 50% output device ordering information device nomenclature device order number logic circuit indicator no. of gates per package temp range identifier technology device function package suffix tape and reel suffix package type tape and reel size NL17SZU04Dft2 nl 1 7 sz u04 df t2 sot-353/ sc70-5/ sc-88a 178 mm, 3000 unit nl17szu04xv5t2 nl 1 7 sz u04 xv5 t2 sot-553 178 mm, 4000 unit
nl17szu04 http://onsemi.com 5 tape trailer (connected to reel hub) no components 160 mm min tape leader no components 400 mm min components direction of feed cavity tape top tape figure 5. tape ends for finished goods t2o pin one opposing sprocket hole (3k reel) figure 6. sot-353/sc70-5/sc-88a reel configuration/orientation t2o pin one opposing sprocket hole (4k reel) figure 7. sot-553 xv5t2 reel configuration/orientation
nl17szu04 http://onsemi.com 6 figure 8. reel dimensions 13.0 mm 0.2 mm (0.512 in 0.008 in) 1.5 mm min (0.06 in) 50 mm min (1.969 in) 20.2 mm min (0.795 in) full radius t max g a reel dimensions 2 tape size 8 mm t and r suffix t2 a max 178 mm (7 in) g 8.4 mm, + 1.5 mm, -0.0 (0.33 in + 0.059 in, -0.00) t max 14.4 mm (0.56 in) figure 9. reel winding direction direction of feed barcode label hole pocket 2for additional tape and reel information, refer to brochure brd8011/d.
nl17szu04 http://onsemi.com 7 package dimensions sot-353 df suffix 5-lead package case 419a-02 issue f notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. 419a-01 obsolete. new standard 419a-02. dim a min max min max millimeters 1.80 2.20 0.071 0.087 inches b 1.15 1.35 0.045 0.053 c 0.80 1.10 0.031 0.043 d 0.10 0.30 0.004 0.012 g 0.65 bsc 0.026 bsc h --- 0.10 --- 0.004 j 0.10 0.25 0.004 0.010 k 0.10 0.30 0.004 0.012 n 0.20 ref 0.008 ref s 2.00 2.20 0.079 0.087 b 0.2 (0.008) mm 12 3 4 5 a g s d 5 pl h c n j k -b- mm inches 0.65 0.025 0.65 0.025 0.50 0.0197 0.40 0.0157 1.9 0.0748
nl17szu04 http://onsemi.com 8 package dimensions sot-553 xv5 suffix 5-lead package case 463b-01 issue o g m 0.08 (0.003) x d 5 pl c j -x- -y- notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeters 3. maximum lead thickness includes lead finish thickness. minimum lead thickness is the minimum thickness of base material. dim a min max min max inches 1.50 1.70 0.059 0.067 millimeters b 1.10 1.30 0.043 0.051 c 0.50 0.60 0.020 0.024 d 0.17 0.27 0.007 0.011 g 0.50 bsc 0.020 bsc j 0.08 0.18 0.003 0.007 k s style 1: pin 1. base 1 2. emitter 1/2 3. base 2 4. collector 2 5. collector 1 a b y 12 3 4 5 s k style 2: pin 1. cathode 2. anode 3. cathode 4. cathode 5. cathode 0.004 0.012 0.059 0.067 0.10 0.30 1.50 1.70 1.35 0.0531 0.5 0.0197 mm inches 0.5 0.0197 1.0 0.0394 0.45 0.0177 0.3 0.0118 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. typicalo parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including typicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indem nify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and re asonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized u se, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employ er. publication ordering information japan : on semiconductor, japan customer focus center 2-9-1 kamimeguro, meguro-ku, tokyo, japan 153-0051 phone : 81-3-5773-3850 on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. nl17szu04/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303-675-2175 or 800-344-3860 toll free usa/canada fax : 303-675-2176 or 800-344-3867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 800-282-9855 toll free usa/canada
|
